DESAIN PISAU MESIN PENCACAH LIMBAH TOPLES PLASTIK LAB PTLR BATAN KAPASITAS 21 KG PER JAM

MUHAMMAD RIDWAN ALI SETIAWAN, . (2021) DESAIN PISAU MESIN PENCACAH LIMBAH TOPLES PLASTIK LAB PTLR BATAN KAPASITAS 21 KG PER JAM. Sarjana thesis, UNIVERSITAS NEGERI JAKARTA.

[img] Text
1. COVER.pdf

Download (1MB)
[img] Text
2. BAB I.pdf

Download (187kB)
[img] Text
3. BAB II.pdf
Restricted to Registered users only

Download (1MB) | Request a copy
[img] Text
4. BAB III.pdf
Restricted to Registered users only

Download (571kB) | Request a copy
[img] Text
5. BAB IV.pdf
Restricted to Registered users only

Download (772kB) | Request a copy
[img] Text
6. BAB V.pdf
Restricted to Registered users only

Download (330kB) | Request a copy
[img] Text
7. DAFTAR PUSTAKA.pdf

Download (61kB)
[img] Text
8. LAMPIRAN.pdf
Restricted to Registered users only

Download (1MB) | Request a copy

Abstract

Limbah toples plastik pada lab PTLR BATAN adalah permasalahan yang sangat serius untuk diatasi. Salah satu solusinya adalah membuat mesin pencacah limbah toples plastik dan sejenisnya. Mesin pencacah tersebut terdiri dari penggerak, poros, pisau cacah dan rangka. Penelitian ini bertujuan untuk mendesain pisau mesin pencacah limbah toples plastik untuk lab PTLR BATAN, dimulai dengan preliminary desain, uji coba gaya aktual mesin pencacah dengan dimensi pisau yang sudah ditentukan mengunakan metode eksperimen. Desain 2D menggunakan software AutoCAD dan dilanjutkan dengan 3D desain menggunakan software Autodesk Inventor. Dari semua data yang telah dianalisis kemudian divalidasi menggunakan software Autodesk Inventor, selanjutnya pisau dibuat untuk dilakukan uji coba. Dari hasil simulasi Inventor didapatkan nilai tegangan Von Mises sebesar 90,74 MPa, dengan perpindahan (Displacement) sebesar 0,0160 mm dan di dapatkan nilai Safety Factor = 3,78 ≥ 3,0. Berdasarkan hasil uji coba secara keseluruhan dari mesin pencacah terhadap limbah toples plastik lab PTLR BATAN diperoleh hasil cacahan yang cukup baik. Plastic jar waste in the PTLR BATAN lab is a very serious problem to overcome with. One solution is to make a shredder machine etc. The shredder machine is consists of electric motors, shafts, shredder blades and frame. This research aims to design a shredder machine blade, starting with a preliminary design, testing the actual force of the shredder machine with the dimensions of the blades that have been determined using the experimental methods. 2D design using AutoCAD software and followed by 3D design using Autodesk Inventor software. From all the data that has been analyzed then it is validated using Autodesk Inventor software, then blade will be created to be tested. From the Inventor simulation results, the Von Mises stress value is 90,74 MPa, with a displacement of 0.0160 mm and the value of Safety Factor = 3,78 ≥ 3.0. Based on the overall test results of the shredder machine for plastic jar waste in Lab PTLR BATAN, the shredded results were quite good

Item Type: Thesis (Sarjana)
Additional Information: 1). Drs. Syamsuir, M.T. ; 2). Drs. Sirojuddin, M.T.
Subjects: Teknologi dan Ilmu Terapan > Teknik Mesin, Mekanika Teknik
Divisions: FT > S1 Pendidikan Teknik Mesin
Depositing User: Users 10099 not found.
Date Deposited: 15 Mar 2021 02:50
Last Modified: 15 Mar 2021 02:50
URI: http://repository.unj.ac.id/id/eprint/14571

Actions (login required)

View Item View Item