MODIFIKASI PIPA KONDENSASI PROSES PENDINGINAN UAP DAN PENGUJIAN ALAT DESTILASI DENGAN MEMANFAATKAN SAMPAH KAYU SEBAGAI SUMBER ENERGI

ACHMAD SOFYAN MAROGHI, . (2017) MODIFIKASI PIPA KONDENSASI PROSES PENDINGINAN UAP DAN PENGUJIAN ALAT DESTILASI DENGAN MEMANFAATKAN SAMPAH KAYU SEBAGAI SUMBER ENERGI. Sarjana thesis, UNIVERSITAS NEGERI JAKARTA.

[img] Text
skripsi full.pdf

Download (2MB)

Abstract

Penelitian ini bertujuan untuk mengetahui hasil kondensasi proses destilasi dari alat yang sudah ada sebelumnya di Lab Otomotif Gedung M, Fakultas Teknik, Universitas Negeri Jakarta yang dikembangkan dengan mengubah pipa kondensasi untuk memaksimalkan hasil dari proses destilasi dengan kadar garam yang rendah, kadar keasaman (ph) yang sesuai SNI dan volume yang dihasilkan dengan menggunakan sampah / limbah kayu sebagai sumber energi untuk mendapatkan air bersih dan tawar. Metode penelitian yang digunakan adalah rekayasa teknik untuk dapat memaksimalkan alat destilasi yang sudah ada dengan merubah pipa kondensasi berdasarkan perhitungan dari persamaan Heat Transfer Konduksi dan memperpendek dimensi pipa dengan cara me-roll, sehingga pipa kondensasi berbentuk spiral. Pengujian dilakukan secara tiga kali, berdasarkan volume air pada level 1 yang berisikan air laut sebanyak 50 Liter, level 2 yang berisikan air laut sebanyak 60 Liter dan level 3 yang berisikan air laut sebanyak 70 Liter dengan menggunakan bahan bakar yang sama sebanyak 10 kg selama 60 menit , yang dibedakan hanya pada banyaknya (kg) bahan bakar pada pembakaran awal. Pengujian dilakukan pada udara bebas atau ruang terbuka. Hasil yang diperoleh dari pengujian ketiga level air yang berbeda menghasilkan kadar garam, dan volume yang berbeda, tetapi untuk kadar keasaman (ph) konstan pada tiap levelnya. Dimana pada level 1 menghasilkan kadar garam 4 ppt, kadar keasaman 6,5 ph dan volume air 450 ml, sedangkan pada level 2 menghasilkan kadar garam 5 ppt, kadar keasaman 6,5 ph dan volume air 700 ml kemudian pada level 3 menghasilkan kadar garam 6 ppt, kadar keasaman 6,5 ph dan volume air 1000 ml. Yang mempengaruhi bedanya hasil dari proses destilasi adalah volume air yang berbeda dan banyaknya bahan bakar pada awal pembakaran. The purpose of this research to determine the result of the condensation process of distillation existing tools in the automotive lab building M, Faculty of Engineering, State University of Jakarta developed by changing the condensation pipe to maximize the result from distillation processes with low salinity, acidity (ph) in accordance with SNI and the volume is generated by using garbage / waste wood as an energy source for clean water and fresh water. The method used is Technical Engineer in order to maximize the existing distillation equipment by changing the condensation pipe by calculation of the equation Heat Transfer conduction and shorten the pipe dimensions with how to roll so that condensation pipe shaped spiral. Tests are done three times, based on the volume of water at level 1 which contains as much as 50 liters of sea water. Level 2 which contains as much as 60 liters of sea water and level 3 which contains as much as 70 liters of sea water using the same fuel as much as 10 kg for 60 minutes which are distinguished only at the number (kg) fuel at the start of combustion. The tests carried out on free air or outdoors. The results of the third test the different water levels resulted in salinity and a different volume but for acidity (ph) constant at each level. Where at level 1 produces 4 ppt of salinity, acidity of 6.5 pH and water volume of 450 ml, while at level 2 produces 5 ppt of salinity, acidity of 6.5 pH and water volume of 700 ml then at level 3 produces 6 ppt of salinity, acidity of pH 6.5 and the volume of 1000 ml of water. That affects the difference between the result of the distillation process is a different volume of water and the amount of fuel at the start of combustion.

Item Type: Thesis (Sarjana)
Additional Information: 1) Dr. Darwin Rio Budi Syaka, S.T, M.T, 2) Ahmad Kholil, S.T, M.T
Subjects: Teknologi dan Ilmu Terapan > Teknik Mesin, Mekanika Teknik
Divisions: FT > S1 Pendidikan Teknik Mesin
Depositing User: sawung yudo
Date Deposited: 21 Apr 2022 06:10
Last Modified: 21 Apr 2022 06:10
URI: http://repository.unj.ac.id/id/eprint/27394

Actions (login required)

View Item View Item